simple sketch of centrifugal pump|centrifugal pump schematic diagram : Big box store On this slide, you can see the single stage double suction centrifugal pump. What is special about this pump is the casing and impeller design. If you look at this suction flange, you can see that it is splitting the liquid into two halves. The impeller of this type of pump is designed in such a way that liquid can enter from both sides. On the imp... See more The desired shape of the head capacity (H-Q) curve is determined during analysis of the system. Most specifications call for a continuously rising curve (Figure 1-3) with the percentage rise from the best efficiency point (BEP) determined by system limits and mode of operation.Unstable or hooked curves (Figure 1-4) where the maximum developed head is at some flow greater than .
{plog:ftitle_list}
Where: H bep = Head produced by the pump at BEP (feet) g = Gravitational constant (32.2 ft/sec2) ηH = Hydraulic efficiency, as a decimal. Equation 5 from Jekat 2 approximates the hydraulic efficiency. ηH = 1- 0.8/Q0.25 . Example. The following dimensions were measured from a horizontal, 4 x 6 multistage pump with a twin-volute casing:Learn the basic formula and factors for calculating pump efficiency, and why it is important for energy saving and system design. This article also explains the difference between pump efficiency and wire-to-water efficiency, and the challenges of improving pump efficiency. See more
The image shown here is the single stage, closed impeller centrifugal pump schematic diagram. This is a typical pump cross-section. Centrifugal pumps are widely used in various industries for the transportation of fluids. They work on the principle of converting rotational energy from a motor into kinetic energy in the fluid being pumped. Let's delve deeper into the components and working of a centrifugal pump.
The image below shows the cut section of the single-stage pump with an open impeller design. This is the simplest diagram of the pump, which shows only major parts such as the body, impeller, and suction–discharge flanges. See more
Components of a Centrifugal Pump
A centrifugal pump consists of several key components that work together to facilitate the pumping process. These components include:
1. **Impeller**: The impeller is the rotating component of the pump that imparts energy to the fluid. It is typically made of metal or plastic and has curved blades that accelerate the fluid radially outward.
2. **Casing**: The casing is the outer shell of the pump that encloses the impeller and volute. It is designed to direct the flow of fluid and increase the pressure.
3. **Volute**: The volute is a curved funnel-shaped casing that surrounds the impeller. It helps in converting kinetic energy into pressure energy.
4. **Shaft**: The shaft connects the motor to the impeller and transmits the rotational energy to the impeller.
5. **Bearings**: Bearings support the shaft and reduce friction during operation.
6. **Seals**: Seals prevent leakage of fluid from the pump and maintain pressure.
Working of a Centrifugal Pump
When the motor is switched on, it rotates the impeller at high speeds. The rotation of the impeller creates a centrifugal force that pushes the fluid towards the outer edges of the impeller. As the fluid moves radially outward, it gains kinetic energy. The fluid is then directed into the volute, where the kinetic energy is converted into pressure energy.
The pressure energy generated by the pump allows the fluid to be pushed through the discharge outlet and into the piping system. The pump continues to operate until the desired flow rate and pressure are achieved.
Types of Centrifugal Pumps
There are several types of centrifugal pumps based on their design and application. Some common types include:
1. **Single Stage Centrifugal Pump**: This type of pump has only one impeller and is suitable for low to medium flow rates.
2. **Multi-Stage Centrifugal Pump**: These pumps have multiple impellers stacked in series and are used for high-pressure applications.
3. **Vertical Centrifugal Pump**: In this design, the motor is mounted above the pump, making it suitable for applications where space is limited.
4. **Submersible Centrifugal Pump**: These pumps are designed to be submerged in the fluid being pumped and are commonly used in wastewater treatment plants.
5. **Self-Priming Centrifugal Pump**: This type of pump has the ability to evacuate air from the suction line and prime itself, making it ideal for applications where the pump is located above the fluid level.
The image shown here is the single stage, closed impeller centrifugal pump schematic diagram. This is a typical pump cross-section. You
Pumps with entrained air can experience a myriad of issues, not to mention headaches for their operators. Think you may have an issue with air in your pump? Read on to learn the symptoms, and some of the most common .
simple sketch of centrifugal pump|centrifugal pump schematic diagram